XSJ flow integrating instrument
1. Technical specification
1).Power supply ：220 VAC power instrument : 220 V ± 10%, power consumption is less than 7VA; 24 VDC power instrument: 24 V± 10%, power consumption is less than 5 VA; 12 VDC power instrument: 9 V~20V, power consumption is less than 5 VA .
2).Working environment: 0 ℃ to 50 ℃, humidity below 90% R.H
3). Display ：Instantaneous flow four LED display, 0 ~ 9999, the decimal point position Settings as required , Cumulative flow 8-bit LED display, 0 ~ 99999999, the decimal point position is the same as the instantaneous flow rate .
4). Input signal ：direct current ：4mA~20mA，0mA~10mA，0mA~20mA. It can select direct voltage by the setting：1V~5V DC，0V~5V DC. It can select pulse by the setting：0.1Hz~10KHz
5).Basic error ：less than ±0.2%F.S
6). Measurement control cycle: 0.2 seconds
2. Parameter selection table
|
Content
|
Code and introduction
|
|
XSJ
|
Double display, supply the transmitter power
|
|
Dimension
|
A-
|
Horizontal type160×80×125 or
vertical type 80×160×125（W×H×L）
|
|
B-
|
96×96×112(W×H×L)
|
|
C-
|
96×48×112(W×H×L)
Intelligent horizontal type single show
|
|
Panel form
|
H
|
Horizontal type
|
|
S
|
Vertical type
|
|
F
|
Square type
|
|
Display
|
1
|
8-bit LED display, single cumulative value
|
|
2
|
8 + 4 bit LED display, double cumulative values, instantaneous value also showed (type A, B) limited
|
|
Input signal
|
I
|
Direct current（4~20）mA or （0~10）mA
or（0~20）mA
|
|
V
|
Direct voltage（0~5）V DC 、（1~5）V DC
|
|
K
|
Pulse input （0.1~10）K HZ
|
|
Number of stations
|
T□
|
TO: alarm free T1~T2:1~2a.m. alarm
|
|
Supply power
|
B0
|
Without supply power
|
|
B1
|
supply24V DC, error less than±5％，50mA
|
|
B2
|
Supply 12V DC, error less than ±5％，50mA
|
|
B3
|
Other
|
|
Transmitting output
（Independent power supply, complete isolation.10bit D/A，error less than ±0.5%，or 12bit D/A，error less than±0.2%
|
A0
|
Without output
|
|
A1
|
Current output(4~20）mA、（0~10）mA或（0~20）mA
|
|
A2
|
Voltage output (0~5）V、（1~5）V
|
|
A3
|
Voltage output (0~10）V
|
|
A4
|
Other output
|
|
Communication interface（Independent power supply, complete isolation，2400~19.2K, answering delay is less than 500μs）
|
S0
|
Without communication interface
|
|
S1
|
RS-232
|
|
S2
|
RS-485
|
|
Instrument power
|
V0
|
220V AC
|
|
V1
|
24V DC
|
|
V2
|
12V DC
|
|
Printing function
|
P
|
P means with printing function, without p means without printing function
|
|
Blackout logging (only double display instrument) (A and B type instrument only)
|
D
|
D means with the function of outage record
|
|
Cumulative volume pulse output
|
O
|
O means with cumulative pulse output function
|
|
Non-standard features
|
N
|
N means non-standard features
|
